Blog

Technical Parameters of the Nitrogen Generator

Mar 18, 2026 Leave a message

Mass
This refers to the weight of a gas, typically expressed in milligrams (mg), grams (g), kilograms (kg), or tons (t). Volume refers to the internal capacity of the container housing the gas; it is commonly expressed in cubic millimeters (mm³), cubic centimeters (cm³), or cubic meters (m³). Specific volume is the volume occupied by a unit weight of a substance; it is denoted by the symbol *V*. For gases, specific volume is measured in m³/kg, while for liquids, it is measured in l/kg.


Pressure, Force per Unit Area, Atmospheric Pressure, Absolute Pressure, Relative Pressure
The force generated by the impact of moving gas molecules against the walls of a container is termed *pressure*. The pressure exerted upon a unit area of ​​the container's surface is termed *force per unit area* (or simply *pressure*). Conventionally, units such as millimeters of mercury (mmHg) or force per square centimeter (cm²) are used; however, the internationally standardized (legal metrology) units are the Pascal (Pa), kilopascal (kPa), and megapascal (MPa). Through conversion: 1 mmHg = 133.3 Pa = 0.1333 kPa; 1 MPa = 1000 kPa = 1,000,000 Pa; and 1 ATA = 0.1 MPa.
The pressure exerted upon the Earth's surface-or objects situated on it-by the thick layer of atmosphere enveloping the planet is known as *atmospheric pressure*, denoted by the symbol *B*. Pressure acting directly upon the surface of a container or object is termed *absolute pressure*; absolute pressure values ​​are measured relative to a starting point of absolute vacuum and are denoted by the symbol *P*ABS.
Pressure measured using instruments such as pressure gauges, vacuum gauges, or U-tube manometers is termed *gauge pressure* (also known as *relative pressure*); gauge pressure is measured relative to atmospheric pressure and is denoted by the symbol *P*g. The relationship among these three quantities is expressed as: *P*ABS = *B* + *P*g.

 

Temperature, Absolute Temperature, Relative Temperature, Critical Temperature, Critical Pressure
Temperature represents the statistical average of the thermal motion of a substance's molecules. Gas temperature is a manifestation of the thermal motion of gas molecules. Gas temperature is commonly expressed in degrees Celsius (°C), with the freezing point of water defined as 0°C. In physics, *absolute temperature* is frequently employed, denoted by the symbol "K." Absolute temperature establishes –273°C as its zero point. The relationship between Celsius and absolute temperature is given by the formula: *T* = *t* + 273. Additionally, British scientists often utilize the *Fahrenheit* scale, denoted by the symbol °F. Since any gas can be liquefied under specific conditions of temperature and pressure, the higher the temperature, the greater the pressure required for liquefaction. However, once the temperature exceeds a certain threshold, no amount of increased pressure-no matter how great-can induce liquefaction. This specific temperature is known as the *critical temperature*, and the minimum pressure required at this temperature is termed the *critical pressure*.
The *dew point* refers to the temperature at which the moisture present in a gas transitions from an unsaturated vapor state to a saturated vapor state. When this transition occurs, minute droplets of dew begin to form; the temperature at which these droplets first appear is defined as the dew point. Since the dew point is pressure-dependent, a distinction is made between the *atmospheric dew point* (or normal-pressure dew point) and the *pressure dew point*. The atmospheric dew point denotes the temperature at which moisture condenses under standard atmospheric pressure, whereas the pressure dew point refers to the condensation temperature of moisture under a specific, elevated pressure. A conversion relationship exists between these two values ​​(which can be determined via conversion tables); for instance, if the pressure dew point is 5°C at a pressure of 0.7 MPa, the corresponding atmospheric dew point (at 0.101 MPa) would be -20°C. In the gas industry, unless explicitly stated otherwise, any reference to the "dew point" is understood to signify the atmospheric dew point. *Vaporization* describes the process by which a substance transitions from a liquid state to a gaseous state; this process encompasses both evaporation and boiling. *Condensation*, conversely, describes the process by which a gas transitions into a liquid.

 

Purity
Purity is a critical technical parameter for gases. Taking nitrogen as an example: according to national standards, nitrogen purity is categorized into three grades-Industrial-grade Nitrogen, Pure Nitrogen, and High-purity Nitrogen. Their respective purity levels are 99.5% (with O₂ content ≤ 0.5%), 99.99% (with O₂ content ≤ 0.01%), and 99.999% (with O₂ content ≤ 0.001%).


Flow Rate, Volumetric Flow Rate, and Mass Flow Rate
*Flow rate* refers to the quantity of gas passing through any given cross-section of a conduit per unit of time during the gas's flow. Flow rate can be expressed in two ways: as *volumetric flow rate* or as *mass flow rate*. The former denotes the volume of gas passing through a specific cross-section of the pipeline, while the latter denotes the mass of gas passing through it. In the gas industry, volumetric flow rate is the standard metric typically employed, measured in units of m³/h (or L/h). Since gas volume is dependent on temperature, pressure, and humidity, for the sake of comparability, the commonly cited volumetric flow rate typically refers to "standard conditions" (defined as a temperature of 20°C, a pressure of 0.101 MPa, and a relative humidity of 65%). Under these conditions, the flow rate is expressed in units of Nm³/h, where the "N" signifies "standard conditions."
Air possesses compressibility; when mechanical work is performed on air by an air compressor-thereby reducing its volume and increasing its pressure-the resulting substance is known as compressed air. Compressed air contains numerous impurities: 1. Water (including water mist, water vapor, and condensate); 2. Oil (including oil droplets and oil vapor); and 3. Various solid substances (such as rust particles, metal dust, rubber dust, tar granules, and fine particles from filter media or sealing materials). Furthermore, it may contain various harmful chemical substances that produce odors. Water vapor can be removed from compressed air through methods such as pressurization, cooling, or adsorption. Liquid water can be removed through methods such as heating, filtration, or mechanical separation.

 

Adsorption and Membrane Permeation
Adsorption is the selective concentration of one or more components within a gas mixture onto the surface of a porous solid. The component being adsorbed is referred to as the *adsorbate*, while the porous solid is termed the *adsorbent*. The binding force between the adsorbent and the adsorbate is typically a chemical bond; the subsequent release (desorption) of the adsorbate is achieved by raising the temperature or by reducing the partial pressure of that specific component within the gas mixture. In a distinct scenario-known as *chemisorption*-the adsorbate undergoes a chemical reaction with the solid adsorbent; generally, chemisorbed materials cannot be regenerated.
Membrane permeation, in the context of gas purification, refers to the process wherein a polymeric membrane separates gases based on the selective permeation of one or more gas components from one side of the membrane to the other. The specific component in question dissolves into the surface of the polymer membrane and subsequently migrates through the membrane, driven by a concentration gradient. This concentration gradient is maintained by ensuring that the partial pressure of the specific component on one side of the membrane remains higher than its partial pressure on the opposing side.

info-800-800

Send Inquiry